You may recall a Limestone job I did recently at a Manchester country club in Hale. This Anti-Slip porcelain floor was installed at the same location in the passageway on route to the toilets and in the toilets themselves. Slips and falls can be a huge problem for buildings with public areas and so tiles which have been etched to make a normally smooth surface rough make perfect sense, the downside of course is that those rough surfaces trap dirt and are difficult to clean. Tile Doctor have a chemical Anti-Slip alternative that only activates when the tile get wet that doesn’t require the tile to be etched but it does need to re-applied every few years.
Cleaning Anti Slip Floor Tiles
The floor tiled need a deep clean to bring out the ingrained dirt so we applied a strong solution of Tile Doctor Pro-Clean using two parts water to one part Pro-Clean and left it to soak into the tile for twenty minutes. The solution was then scrubbed into the tile using a rotary machine fitted with a black scrubbing pad. You could see the dirt coming out the pores of the tile and the resultant soiled solution was removed using a wet vacuum before washing the tiles down with clean water.
Including the ladies, gents and hallway there was a lot of floor area to cover and some of the stubborn areas had to be re-treated so it was a long job but I think you will agree the floor now looks great.
Before and after photograph below of a Quarry Tiled floor at a school in Dunstable that was in such a bad state we had to apply grout colourant to the floor. Quarry tiles are fairly indestructible so ideal for use in schools etc. where they will see a lot of foot traffic and abuse, having said that they will fade with wear over time and naturally the grout can become ingrained with dirt if not protected.
Cleaning Quarry Tiles
It had been a while since the Quarry Tiles and Grout had been given a really deep clean to so we mixed a dilution of Tile Doctor Pro-Clean 50/50 with NanoTech UltraClean and applied it to the floor and left to soak in for around 10 minutes; Pro-Clean is a multipurpose alkaline cleaning product designed specifically for cleaning tile and stone and NanoTech UltraClean adds tiny abrasive particles into the solution to make a more effective cleaner. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad and the grout lines scrubbed by hand using a stiff brush. The floor was then rinsed thoroughly with water which was removed using a wet vacuum, once the Quarry tiles were dry it was possible to spot the areas in need of further attention and these were scrubbed by hand together with more of the Pro-Clean/UltraClean mix and a steamer. At this stage it became apparent that that although the grout had improved it was too far gone and never going to make the grade and either needed to re-done or as per our suggestion re-coloured.
For floor grout we always recommend the use of an epoxy grout colouring product which not only completely covers the grout making it look new again but also provides a permanent barrier that prevents the grout from staining in future. They can be quite time consuming to apply however especially if you have a small format Quarry tile with lots of grouting.
Sealing Quarry Tiles
Once happy with the floor and it had time to dry off it was sealed with six coats of Tile Doctor High Shine Sealer which will provide future surface stain protection and also leaves a nice deep shine on the floor. It took a long time but I think you will agree from the before and after photograph below we managed quite a transformation.
This Limestone tiled floor was installed in a holiday rental cottage in Chipping Norton which had a regular change of occupants and was in need of a deep clean and polish. To deep clean stone floors such as Limestone, Marble and Travertine the floor needs to be burnished with diamond encrusted pads.
Cleaning Limestone Floor Tiles
The floor was given a quick wash with Tile Doctor Neutral Cleaner in order to remove any surface grit and then cleaned using a set of Burnishing pads fitted to a rotary machine. The burnishing pads come in four different types and you work your way through them starting off with a course stripper pad with a little just water and then carry on with the white pad and then the yellow pad until the floor is thoroughly cleaned and any previous sealer removed. Next step was to use Tile Doctor Pro-Clean along the grout lines with a stiff brush to get the grout cleaner. To bring up the polish on the Limestone tiles I used a polishing pad which is the last in the set of the four burnishing pads. The floor was still wet at this stage so an air dryer machine was used to speed up the drying process.
Sealing Limestone Floor Tiles
Once the floor was dry we set about sealing it using two coats of Tile Doctor Colour Grow which is a colour enhancing sealer designed to provide maximum stain protection on natural stone floors whilst bringing out the deep colour in the stone. The last step was to buff the floor to a nice shine with a rotary machine fitted with a white pad.